en:tech:gw60
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| en:tech:gw60 [2022/09/26 08:59] – [Donate] bullar | en:tech:gw60 [2026/08/12 13:57] (current) – claude | ||
|---|---|---|---|
| Line 4: | Line 4: | ||
| If you want to include the shutters in home automation, you need a corresponding control. If you don't want to retrofit the roller shutters yourself, you can switch to electronic belt winders. These are fully developed but require an external power supply. There are several manufacturers on the market who also have a wireless remote control in their range. Almost all of them have in common that they rely on their own standards and need a headquarters from the respective manufacturer. If you want to avoid this, you have to find your own, open solution. | If you want to include the shutters in home automation, you need a corresponding control. If you don't want to retrofit the roller shutters yourself, you can switch to electronic belt winders. These are fully developed but require an external power supply. There are several manufacturers on the market who also have a wireless remote control in their range. Almost all of them have in common that they rely on their own standards and need a headquarters from the respective manufacturer. If you want to avoid this, you have to find your own, open solution. | ||
| - | {{ : | + | {{ :media:tech:gw60: |
| - | {{: | + | {{:media:tech:gw60: |
| An inexpensive electronic belt winder is the [[https:// | An inexpensive electronic belt winder is the [[https:// | ||
| Line 18: | Line 18: | ||
| My solution looks like this: | My solution looks like this: | ||
| - | {{ : | + | {{ :media:tech:gw60: |
| On the left, the connection to the GW60 is originally designed as a spring contact. Unfortunately I couldn' | On the left, the connection to the GW60 is originally designed as a spring contact. Unfortunately I couldn' | ||
| Line 27: | Line 27: | ||
| The button and the LED are provided for connection to the TRÅDFRI control unit. Once trained, we no longer need either. The available space is sufficient to accommodate all components. | The button and the LED are provided for connection to the TRÅDFRI control unit. Once trained, we no longer need either. The available space is sufficient to accommodate all components. | ||
| - | {{ : | + | {{ :media:tech:gw60: |
| In order for the cover to fit on the housing, the PCB should be only 1mm thick like the original. | In order for the cover to fit on the housing, the PCB should be only 1mm thick like the original. | ||
| Line 34: | Line 34: | ||
| With a caliper, the housing is quickly created in Fusion360 and then looks like this: | With a caliper, the housing is quickly created in Fusion360 and then looks like this: | ||
| - | {{ :de: | + | {{ :media:tech:gw60: |
| As shown, it can be printed in the 3D printer without support structures. The small block on the right serves to protect the POGO pins and can be pushed onto them. | As shown, it can be printed in the 3D printer without support structures. The small block on the right serves to protect the POGO pins and can be pushed onto them. | ||
| - | {{: | + | {{:media:tech:gw60: |
| - | {{: | + | {{:media:tech:gw60: |
| The PCB antenna looks out of the housing for better reception. Although the module disappears in the belt case when the GW60 is installed, I did not have any connection problems with the TRÅDFRI buttons or the gateway. | The PCB antenna looks out of the housing for better reception. Although the module disappears in the belt case when the GW60 is installed, I did not have any connection problems with the TRÅDFRI buttons or the gateway. | ||
| Line 47: | Line 47: | ||
| The TRÅDFRI module is now electrically and mechanically connected to the GW60, but the GW60 controller cannot yet do anything with the data. To do this, the existing firmware must be expanded. The GW60 is controlled by a PIC16F690 with an on-board programming interface. The PICkit3, which is also available as a China replica, is an inexpensive programmer. | The TRÅDFRI module is now electrically and mechanically connected to the GW60, but the GW60 controller cannot yet do anything with the data. To do this, the existing firmware must be expanded. The GW60 is controlled by a PIC16F690 with an on-board programming interface. The PICkit3, which is also available as a China replica, is an inexpensive programmer. | ||
| - | {{ : | + | {{ :media:tech:gw60: |
| To be able to read out the original firmware first, we have to connect the GW60 board to the PICkit3. The test pads on the back of the GW60 PCB are very helpful. There you can easily solder the 5 cables. | To be able to read out the original firmware first, we have to connect the GW60 board to the PICkit3. The test pads on the back of the GW60 PCB are very helpful. There you can easily solder the 5 cables. | ||
| - | {{ : | + | {{ :media:tech:gw60: |
| MICROCHIP provides a free IDE with the name [[https:// | MICROCHIP provides a free IDE with the name [[https:// | ||
| Line 839: | Line 839: | ||
| If you have to update the software again, I've put the programming interface outside. But it is only nice-to-have... | If you have to update the software again, I've put the programming interface outside. But it is only nice-to-have... | ||
| - | {{ : | + | {{ :media:tech:gw60: |
| ==== Downloads ==== | ==== Downloads ==== | ||
| - | * {{:tech:GW60_ZIGBEE_BOM.pdf | Bill of Material (BOM)}} | + | * {{:media:tech:gw60: |
| - | * {{:tech:GW60-ZIGBEE.brd.zip |PCB}} Eagle format (.brd) | + | * {{:media:tech:gw60:gw60-zigbee.brd.zip |PCB}} Eagle format (.brd) |
| - | * {{:tech:GW60_Zigbee v14.stl.zip| Housing}} (STL file) | + | * {{:media:tech:gw60: |
| ==== Donate ==== | ==== Donate ==== | ||
en/tech/gw60.1664182744.txt.gz · Last modified: (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial 4.0 International
