TechWiki

User Tools

Site Tools

Trace:
tech:3d_huxley

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
tech:3d_huxley [2016/02/13 19:15] – bullartech:3d_huxley [2026/08/12 12:15] (current) – external edit 127.0.0.1
Line 1: Line 1:
 ====== HUXLEY ====== ====== HUXLEY ======
  
-{{:tech:huxley_kit_big.png?nolink&300|}}+{{:media:tech:3d_huxley:huxley_kit_big.png?nolink&300|}}
  
 Frame: [[https://reprappro.com/documentation/huxley/]] \\ Frame: [[https://reprappro.com/documentation/huxley/]] \\
-Controller (Melzi): [[http://reprap.org/wiki/Melzi]]+Controller (Melzi): [[http://reprap.org/wiki/Melzi]] \\ 
 +RepRap Wiki: [[http://reprap.org/wiki/The_incomplete_RepRap_Prusa_Mendel_beginner's_guide|The incomplete RepRap Prusa Mendel beginner's guide]]
  
 ==== Melzi Bluetooth modification ==== ==== Melzi Bluetooth modification ====
Line 10: Line 11:
 In order to get rid of the USB connection between Melzi and the PC one may like to use Bluetooth. There is a cheap module available in the market called 'JY-MCU' (vendor Shenzhen Jiayuan Electronic Co.,Ltd.). In order to get rid of the USB connection between Melzi and the PC one may like to use Bluetooth. There is a cheap module available in the market called 'JY-MCU' (vendor Shenzhen Jiayuan Electronic Co.,Ltd.).
  
-{{:tech:jy-mcu_b.jpg?nolink&200 |Bottom}} {{:tech:jy-mcu_f.jpg?nolink&200 |Top}}  \\+{{:media:tech:3d_huxley:jy-mcu_b.jpg?nolink&200 |Bottom}} {{:media:tech:3d_huxley:jy-mcu_f.jpg?nolink&200 |Top}}  \\
  
 ===Change setting=== ===Change setting===
Line 25: Line 26:
 On Melzi one of the unused buffer of soldered IC 4050D takes over the mandatory level-shifting (5V -> 3.3V). Overall only 5 wires have to be soldered. Note that the TXD outputs are connected in parallel which is not recommended. On Arduino boards the serial chip is connected to the main IC via 1kOhm resistors for this reason. This are not present in the Melzi board design. On Melzi one of the unused buffer of soldered IC 4050D takes over the mandatory level-shifting (5V -> 3.3V). Overall only 5 wires have to be soldered. Note that the TXD outputs are connected in parallel which is not recommended. On Arduino boards the serial chip is connected to the main IC via 1kOhm resistors for this reason. This are not present in the Melzi board design.
  
-{{:tech:bt_connection.png?nolink&300|}}+{{:media:tech:3d_huxley:bt_connection.png?nolink&300|}}
  
 ===Connect via Bluetooth=== ===Connect via Bluetooth===
Line 35: Line 36:
 The solution is described on [[http://www.thingiverse.com/thing:927030|Thingiverse]]. The solution is described on [[http://www.thingiverse.com/thing:927030|Thingiverse]].
  
-{{:tech:extrusion_fan.png?nolink&350 |}}  {{ :tech:sig_201532206152247903.jpg?nolink&310|}} \\+{{:media:tech:3d_huxley:extrusion_fan.png?nolink&350 |}}  {{ :media:tech:3d_huxley:sig_201532206152247903.jpg?nolink&310|}} \\
  
 Radial fan: [[http://www.ystech.com.tw/yensun/imgFile/BD5015-2.pdf|Y.S.TECH BD125015MB 12V/0.125A]] Radial fan: [[http://www.ystech.com.tw/yensun/imgFile/BD5015-2.pdf|Y.S.TECH BD125015MB 12V/0.125A]]
Line 43: Line 44:
 In order to get for print area (Z dimension) I positioned the PCB in top. The original printed PCB holder (4pcs.) ate reused. The PCB is mounted on a laser-cutter 1.5mm thick [[http://www.kraftplex.com/kraftplex/|Kraftplex]]. In order to get for print area (Z dimension) I positioned the PCB in top. The original printed PCB holder (4pcs.) ate reused. The PCB is mounted on a laser-cutter 1.5mm thick [[http://www.kraftplex.com/kraftplex/|Kraftplex]].
  
-{{:tech:huxley_pcb_holder.png?300|}} {{ :tech:melzi_pcb_cover.png?350|}} +{{:media:tech:3d_huxley:huxley_pcb_holder.png?300|}} {{ :media:tech:3d_huxley:melzi_pcb_cover.png?350|}}  
 + 
 + 
 +==== Melzi LCD Controller ==== 
 + 
 +See [[http://www.wamungo.de/PrintModel/Detail/Hausgemachte-Panelolu-2-I2C-20-x-4-LCD-mit-Sound-f-r-weniger-dann-12-Euro-inkl-einfache-ISP10-sound-Modefication-538d262c8970280f88b7c72b|LCD Controller]]. 
 + 
 +{{:media:tech:3d_huxley:detail_lcd_case_display_large.jpg?nolink&300|}} 
 + 
 +=== I2C -> LCD converter (LMC1602) === 
 + 
 +[[http://www.exp-tech.de/doc/lcd/1602/LCM1602IICV2%20%20Schematic.pdf|]] 
 + 
 ==== Setup Bed ==== ==== Setup Bed ====
  
Line 56: Line 70:
  
 Init file:  Init file: 
-<file ini>+<file ini huxley.ini>
 [profile] [profile]
 layer_height = 0.1 layer_height = 0.1
Line 338: Line 352:
  
 </file> </file>
- 
- 
  
tech/3d_huxley.1455390936.txt.gz · Last modified: by bullar

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial 4.0 International
CC Attribution-Noncommercial 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki