TechWiki

User Tools

Site Tools

Trace:
tech:3d_prusa

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
tech:3d_prusa [2016/02/13 19:12] – bullartech:3d_prusa [2016/02/21 21:03] – bullar
Line 26: Line 26:
 |offset print area|   40|   36|   0|  mm| |offset print area|   40|   36|   0|  mm|
 |offset extruder 2|  27|  0|  0|  mm| |offset extruder 2|  27|  0|  0|  mm|
 +
 +==== Printer Trouble ====
 +
 +[[https://www.simplify3d.com/support/print-quality-troubleshooting/| Printer trouble]]
 +
 +
 +==== CURA Setup ====
 +
 +INI file:
 +
 +<file ini Prusa_i3.ini>
 +[profile]
 +layer_height = 0.1
 +wall_thickness = 1.0
 +retraction_enable = True
 +solid_layer_thickness = 0.6
 +fill_density = 20
 +print_speed = 50
 +print_temperature = 200
 +print_temperature2 = 200
 +print_temperature3 = 0
 +print_temperature4 = 0
 +print_temperature5 = 0
 +print_bed_temperature = 70
 +support = None
 +platform_adhesion = None
 +support_dual_extrusion = Both
 +wipe_tower = False
 +wipe_tower_volume = 15
 +ooze_shield = False
 +filament_diameter = 1.75
 +filament_diameter2 = 1.75
 +filament_diameter3 = 0
 +filament_diameter4 = 0
 +filament_diameter5 = 0
 +filament_flow = 100.0
 +nozzle_size = 0.5
 +retraction_speed = 40.0
 +retraction_amount = 4.5
 +retraction_dual_amount = 16.0
 +retraction_min_travel = 1.5
 +retraction_combing = All
 +retraction_minimal_extrusion = 0.02
 +retraction_hop = 0.0
 +bottom_thickness = 0.3
 +layer0_width_factor = 100
 +object_sink = 0.0
 +overlap_dual = 0.15
 +travel_speed = 150
 +bottom_layer_speed = 20
 +infill_speed = 0.0
 +solidarea_speed = 0.0
 +inset0_speed = 0.0
 +insetx_speed = 0.0
 +cool_min_layer_time = 5
 +fan_enabled = True
 +skirt_line_count = 1
 +skirt_gap = 3.0
 +skirt_minimal_length = 150.0
 +fan_full_height = 0.5
 +fan_speed = 100
 +fan_speed_max = 100
 +cool_min_feedrate = 10
 +cool_head_lift = False
 +solid_top = True
 +solid_bottom = True
 +fill_overlap = 15
 +perimeter_before_infill = False
 +support_type = Lines
 +support_angle = 60
 +support_fill_rate = 15
 +support_xy_distance = 0.7
 +support_z_distance = 0.15
 +spiralize = False
 +simple_mode = False
 +brim_line_count = 20
 +raft_margin = 5.0
 +raft_line_spacing = 3.0
 +raft_base_thickness = 0.3
 +raft_base_linewidth = 1.0
 +raft_interface_thickness = 0.27
 +raft_interface_linewidth = 0.4
 +raft_airgap_all = 0.0
 +raft_airgap = 0.22
 +raft_surface_layers = 2
 +raft_surface_thickness = 0.27
 +raft_surface_linewidth = 0.4
 +fix_horrible_union_all_type_a = True
 +fix_horrible_union_all_type_b = False
 +fix_horrible_use_open_bits = False
 +fix_horrible_extensive_stitching = False
 +plugin_config = (lp1
 + (dp2
 + S'params'
 + p3
 + (dp4
 + S'xshift'
 + p5
 + V40.0
 + p6
 + sS'zshift'
 + p7
 + V0.0
 + p8
 + sS'yshift'
 + p9
 + V36.0
 + p10
 + ssS'filename'
 + p11
 + S'XYZshift.py'
 + p12
 + sa.
 +object_center_x = -1
 +object_center_y = -1
 +
 +[alterations]
 +start.gcode = ;Sliced at: {day} {date} {time}
 + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 + ;Print time: {print_time}
 + ;Filament used: {filament_amount}m {filament_weight}g
 + ;Filament cost: {filament_cost}
 + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 + ;M109 S{print_temperature} ;Uncomment to add your own temperature line
 + G21        ;metric values
 + G90        ;absolute positioning
 + M82        ;set extruder to absolute mode
 + M107       ;start with the fan off
 + G28 X0 Y0  ;move X/Y to min endstops
 + G28 Z0     ;move Z to min endstops
 + G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 + G92 E0                  ;zero the extruded length
 + G1 F200 E3              ;extrude 3mm of feed stock
 + G92 E0                  ;zero the extruded length again
 + G1 F{travel_speed}
 + ;Put printing message on LCD screen
 + M117 Printing...
 +end.gcode = ;End GCode
 + M104 S0                     ;extruder heater off
 + M140 S0                     ;heated bed heater off (if you have it)
 + G91                                    ;relative positioning
 + G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 + G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 + M84                         ;steppers off
 + G90                         ;absolute positioning
 + ;{profile_string}
 +start2.gcode = ;Sliced at: {day} {date} {time}
 + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 + ;Print time: {print_time}
 + ;Filament used: {filament_amount}m {filament_weight}g
 + ;Filament cost: {filament_cost}
 + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 + ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 + ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 + ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 + G21        ;metric values
 + G90        ;absolute positioning
 + M107       ;start with the fan off
 + G28 X0 Y0  ;move X/Y to min endstops
 + G28 Z0     ;move Z to min endstops
 + G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 + T1                      ;Switch to the 2nd extruder
 + G92 E0                  ;zero the extruded length
 + G1 F200 E10             ;extrude 10mm of feed stock
 + G92 E0                  ;zero the extruded length again
 + G1 F200 E-{retraction_dual_amount}
 + T0                      ;Switch to the first extruder
 + G92 E0                  ;zero the extruded length
 + G1 F200 E10             ;extrude 10mm of feed stock
 + G92 E0                  ;zero the extruded length again
 + G1 F{travel_speed}
 + ;Put printing message on LCD screen
 + M117 Printing...
 +end2.gcode = ;End GCode
 + M104 T0 S0                     ;extruder heater off
 + M104 T1 S0                     ;extruder heater off
 + M140 S0                     ;heated bed heater off (if you have it)
 + G91                                    ;relative positioning
 + G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 + G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 + M84                         ;steppers off
 + G90                         ;absolute positioning
 + ;{profile_string}
 +start3.gcode = ;Sliced at: {day} {date} {time}
 + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 + ;Print time: {print_time}
 + ;Filament used: {filament_amount}m {filament_weight}g
 + ;Filament cost: {filament_cost}
 + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 + ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 + ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 + ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 + G21        ;metric values
 + G90        ;absolute positioning
 + M107       ;start with the fan off
 + G28 X0 Y0  ;move X/Y to min endstops
 + G28 Z0     ;move Z to min endstops
 + G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 + T2                      ;Switch to the 3rd extruder
 + G92 E0                  ;zero the extruded length
 + G1 F200 E10             ;extrude 10mm of feed stock
 + G92 E0                  ;zero the extruded length again
 + G1 F200 E-{retraction_dual_amount}
 + T1                      ;Switch to the 2nd extruder
 + G92 E0                  ;zero the extruded length
 + G1 F200 E10             ;extrude 10mm of feed stock
 + G92 E0                  ;zero the extruded length again
 + G1 F200 E-{retraction_dual_amount}
 + T0                      ;Switch to the first extruder
 + G92 E0                  ;zero the extruded length
 + G1 F200 E10             ;extrude 10mm of feed stock
 + G92 E0                  ;zero the extruded length again
 + G1 F{travel_speed}
 + ;Put printing message on LCD screen
 + M117 Printing...
 +end3.gcode = ;End GCode
 + M104 T0 S0                     ;extruder heater off
 + M104 T1 S0                     ;extruder heater off
 + M104 T2 S0                     ;extruder heater off
 + M140 S0                     ;heated bed heater off (if you have it)
 + G91                                    ;relative positioning
 + G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 + G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 + M84                         ;steppers off
 + G90                         ;absolute positioning
 + ;{profile_string}
 +start4.gcode = ;Sliced at: {day} {date} {time}
 + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
 + ;Print time: {print_time}
 + ;Filament used: {filament_amount}m {filament_weight}g
 + ;Filament cost: {filament_cost}
 + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
 + ;M104 S{print_temperature} ;Uncomment to add your own temperature line
 + ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
 + ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
 + ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
 + G21        ;metric values
 + G90        ;absolute positioning
 + M107       ;start with the fan off
 + G28 X0 Y0  ;move X/Y to min endstops
 + G28 Z0     ;move Z to min endstops
 + G1 Z15.0 F{travel_speed} ;move the platform down 15mm
 + T3                      ;Switch to the 4th extruder
 + G92 E0                  ;zero the extruded length
 + G1 F200 E10             ;extrude 10mm of feed stock
 + G92 E0                  ;zero the extruded length again
 + G1 F200 E-{retraction_dual_amount}
 + T2                      ;Switch to the 3rd extruder
 + G92 E0                  ;zero the extruded length
 + G1 F200 E10             ;extrude 10mm of feed stock
 + G92 E0                  ;zero the extruded length again
 + G1 F200 E-{retraction_dual_amount}
 + T1                      ;Switch to the 2nd extruder
 + G92 E0                  ;zero the extruded length
 + G1 F200 E10             ;extrude 10mm of feed stock
 + G92 E0                  ;zero the extruded length again
 + G1 F200 E-{retraction_dual_amount}
 + T0                      ;Switch to the first extruder
 + G92 E0                  ;zero the extruded length
 + G1 F200 E10             ;extrude 10mm of feed stock
 + G92 E0                  ;zero the extruded length again
 + G1 F{travel_speed}
 + ;Put printing message on LCD screen
 + M117 Printing...
 +end4.gcode = ;End GCode
 + M104 T0 S0                     ;extruder heater off
 + M104 T1 S0                     ;extruder heater off
 + M104 T2 S0                     ;extruder heater off
 + M104 T3 S0                     ;extruder heater off
 + M140 S0                     ;heated bed heater off (if you have it)
 + G91                                    ;relative positioning
 + G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
 + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
 + G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
 + M84                         ;steppers off
 + G90                         ;absolute positioning
 + ;{profile_string}
 +support_start.gcode = 
 +support_end.gcode = 
 +cool_start.gcode = 
 +cool_end.gcode = 
 +replace.csv = 
 +preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 + ;This code is added before the T(n)
 +postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
 + ;This code is added after the T(n)
 +</file>
tech/3d_prusa.txt · Last modified: 2016/02/21 21:25 by bullar

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial 4.0 International
CC Attribution-Noncommercial 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki